![]() While chargers slowly power up a battery, raising its charge level over time, a jumper produces a fast burst of power to quickly start a dead battery. Chargers with USB ports can even be used to charge smartphones, tablets, and other devices.Ī battery charger and a battery jumper are two separate devices, but that doesn’t mean you can’t pick up a unit that can do both. Some portable car battery chargers can also charge the batteries for lawn mowers, jet skis, and other powered tools and toys. Is your car battery a 12-volt or a six-volt? Lead-acid or lithium-ion? Make sure the portable car battery charger can handle your vehicle’s battery before buying. Some portable car battery chargers can only charge a few types of batteries, while others are more flexible. Older batteries have a harder time holding onto a charge and drain more easily than new batteries. ![]() Now if you are after something smaller again for like storage on a motorcycle, these mini pocket jump starters will do the job just fine.Portable car battery chargers are especially handy if your vehicle’s battery is several years old. Check out this post if you would like to learn more about the best jump starters with wireless charging. I don’t need this feature so I just settled for the cheaper unit. Type S does have a more expensive model called the Qi that supports wireless charging for mobile phones. Makes life simple for those that have a flat battery but don’t know how to use a jump starter. The fact that it charges via micro USB ad USB-C means I can always get it charged as these cables are everywhere.Įveryone should have a jump starter in their car and these cheap Costco jump starters make it easy. It works on my Toyota Corolla and Ford Focus. This Costco jump starter type S is very good. So if you were looking to charge an iPhone 11 with a battery capacity of 3,110 mAh you will get around 2.5 charges from the Type S jump starter. So an 8000mAh will last 4 hours if the power draw is increased to 2Ah. Store the Jump Starter in a safe place when not in use.Īn internal 8000mah battery indicates that it has the ability to supply power of 1000ma (1 amp) to a USB device for a maximum of 8 hours. Disconnect the Jump Starter when it is fully charged.Connect the Micro USB Charging Cable to the Micro USB Charge Input Port on the Jump Starter.Plug included Micro USB Charging Cable into included 12V USB Charger then connect to 12V socket in the vehicle.Store the Jump Starter in a safe place when not in use.Do not leave it connected for long periods. Connect the Micro USB or USB-C Charging Cable into the Micro USB Charge Input Port on the Jump Starter.You can also use a 2A USB wall adapter for fast charging (not included). Plug included Micro USB or USB-C Charging Cable into a USB-A port on a computer.Keep the engine running for over 25 minutes to charge the battery or recharge it using a 12v battery tender smart charger.Ĭharging options with miro USB or USB-C At home:.The Costco jump starter will self-power off after 30 seconds. Unplug the cables from the jump starter and recharge the unit for next time.Remove the RED positive cable first and then remove the Black negative cable clamp.If the vehicle starts the jump starter LCD will display “Successful jump unplug cables”.You may have other issues such as a faulty starter motor, bad fuel, short circuit, ignition problem, faulty spark plugs, air filter bad, fuel pump problem, etc. Do not try and start the vehicle more than 3 times otherwise, you could overheat the Type S jump starter.To try again disconnect the jump starter wait 60 seconds and go back to step 1.After 90 seconds the Costco jump starter will stop. During this time the jump starter is putting energy into the battery. You now have 90 seconds to try and crank the vehicle over. ![]() Once the cable clamps are secure the Type S jump starter will display “Ready start vehicle ignition”.If it is flashing red and beeping you may have a polarity issue or a short circuit. Check the LED status on the protection circuit.Always connect the red cable clamp first and then the black cable clamp. Connect the BLACK clamp to the negative terminal of the battery. Connect the RED clamp to the positive terminal of the battery.The LCD display will read ” Clamp cables to battery” Insert the jump cable clamps into the 3-pin port.It will display the battery level as a percentage. To use this jump starter press the mode button to power on the unit.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |